Bill’s Playbook · George’s repair guide
2014 Ram ProMaster 3.0L Diesel
M40/MTA automated-manual transmission: hydraulic shift accumulator replacement
Step-by-step plan, parts list, the three fluids, and the scan-tool routines
VIN 3C6URVHD9EE130571
Updated November 16, 2026 · First written October 6, 2026
Start here, George
Type in your scan tool first. The steps change to match your exact scanner, so you get instructions written for the tool in your hand.
Want the short version? The one-page quick start is at
billsplaybook.info/quick. This page is the full reference behind it.
George, this is the whole job on one page, in order. The factory steps come from Ram’s service text. The way in (battery box out, work from underneath) comes from owners who did this on the Fiat Ducato, which is the same van and the same transmission. Each step is tagged so you know where it comes from:
Factory Ram/FCA service text or owner’s manual (for the scanner hookup, the scanner maker’s own documents) Owner-reported people who did this job, mostly on the Ducato Shop practice normal careful shop work Check on the van confirm it when you’re there
This system holds up to about 1,100 psi. The accumulator is a nitrogen-charged canister that stores that pressure. Never loosen it to let the pressure out. Release the pressure with the scan tool first, turn the ignition off, and unplug the pump. Only then put a wrench on anything hydraulic.
The job at a glance
- Before the van arrives: two phone calls and the parts list (section 1).
- Prove the scanner works on this van before you touch a wrench (section 2).
- Release the pressure with the scanner, ignition off, unplug the pump (section 3).
- Get to it: battery and battery box out, van on stands, work from underneath on the driver’s side (section 4).
- Swap the accumulator (section 5).
- Fill the right fluid to the middle of the sight window, with the pump still unplugged (section 6).
- Put it back and bring the pressure up: pump plugged in, battery in, then bleed (section 7).
- Relearn: Reset of Data Group, then Quick Learn (section 8).
- Prove it: warm it up, check codes, road test, recheck for leaks (section 9).
The three fluids. Only one is touched on this job.
This transmission uses three separate fluids. The accumulator is on the actuator hydraulic circuit, so that is the only fluid you add. Ram’s own wording: “it is imperative that the correct fluids are used.”
| Circuit | Exact fluid | Where it goes | On this job? |
| Actuator hydraulics (the accumulator’s circuit) | Mopar C Series DDCT SAE 75W Hydraulic Fluid P/N 68092638AC (replaces 68092638AA and AB, the older numbers printed in Ram’s manuals). 1-quart bottle. It’s the same fluid as the Dodge Dart DDCT, so Mopar parts counters stock it. | The hydraulic reservoir on the control unit, cap 2 (Ducato owners call it the larger one). Fill to the middle of the sight window, with pressure released. | YES. Buy 2 quarts. |
| Clutch operating circuit | Mopar Brake and Clutch Fluid DOT 4 (P/N 04549625AD, now 68709499AA) | The small reservoir, cap 1, right beside cap 2. Level is 1 inch (25.4 mm) below the top edge. | No. Don’t open it. Only bleed it if the clutch line gets opened. |
| Gearbox | Full synthetic 75W-85 manual transmission fluid, API GL-4 | Gearbox fill plug | No. Leave it alone. |
The two caps sit side by side. Don’t mix them up. Never put DOT 4 or ATF in cap 2, and never put the 75W hydraulic fluid in cap 1. If you’re not sure which cap is which, match them to the figure on the Ram fill page linked below before you open either one.
Factory Both Ram sources name the same fluids: the owner’s supplement and the service manual’s fluid table. That meets Bill’s two-source rule.
1. Before the van arrives
Two phone calls
Call 1
Check on the van Ram dealer parts desk, with Bill’s VIN (3C6URVHD9EE130571). Confirm 68133085AA is the right accumulator for this van. Ask whether it comes with a new O-ring or seal, and if not, which part number to order.
Call 2
Check on the van Ram dealer service desk (or ALLDATA/Mitchell if your shop has it). Ask for the accumulator tightening torque for the 2014 ProMaster M40. No public source we found prints this number, so this guide won’t guess it. If the new part comes with an instruction sheet, that works too.
The official factory source is Stellantis’s paid service site (techauthority.com). It sells short-term access if you want the VIN-specific pages yourself.
Parts and tools
| Item | Price (Oct 2026) | Notes |
| Accumulator, Mopar 68133085AA (replaces 68226975AA) | ~$482 online $711 list | Official Mopar listing. MLR Engineering also sells one under the same number. Confirm with the VIN (call 1). |
| Hydraulic fluid, Mopar 68092638AC, 2 quarts | ~$17–$24 / qt | Fiat’s figure for the whole circuit is 0.7 L. An accumulator swap loses much less, so 2 quarts leaves a spare. Mopar listing |
| AlfaOBD, full paid Android app | $49 | Google Play. The free version doesn’t run the service routines. Android only, not iPhone. |
| OBDLink LX Bluetooth adapter | $89.95 | OBDLink. AlfaOBD lists it for the 2014–2021 ProMaster. |
| Yellow Fiat/Alfa CAN adapter (Adapter 3 style, 16-pin) | ~$15–$30 | AlfaOBD requires the yellow one for ProMasters built before 2022. Not the grey one, not the old 3-pin Fiat plug. Example (Gendan) |
| Battery maintainer / power supply | Shop | A weak battery causes false transmission faults on these vans, and a voltage drop during a relearn can upset the module. Keep it on whenever the scanner is running. |
| Sockets: 22 mm and 27 mm, plus a crow’s-foot and a breaker bar | Shop | Owner-reported A Ducato owner used a 22 mm socket. Alfa owners with the same style of accumulator used 27 mm and said it was very tight. Easiest check: measure the hex on the new accumulator before you start. |
| Torque wrench, jack stands, catch pan, clean rags, gloves and eye protection | Shop | Keep the hydraulic opening spotless. Dirt in this circuit damages the valves. |
2. Prove the scanner works before you touch a wrench
The job depends on four scan-tool routines. Ram calls them Hydraulic Circuit Depressurization, Bleed Hydraulic Circuit, Reset of Data Group and Quick Learn. If your scanner can’t run all four on this van, stop here: the van can be left undrivable halfway through.
Step 1
Shop practice Put the battery maintainer on. Park, set the parking brake, chock the wheels. Engine off. Ram’s manual warns that a low battery can set many false codes on this transmission.
Step 2
Factory Plug the yellow adapter into the OBD port under the dash, then the OBDLink LX into the adapter. Pair the LX with the Android phone by Bluetooth.
Step 3
Factory Turn the ignition ON (engine off) before you connect in AlfaOBD. If it won’t connect, turn the key off for 30 seconds and try again. That tip comes from AlfaOBD’s own help file.
Step 4
Check on the van In AlfaOBD, pick Ram → ProMaster (VF), then the transmission / gearbox (Selespeed, MTA) module. The exact menu labels aren’t published for this van. Use whatever entry AlfaOBD positively identifies as the transmission controller, and don’t force a Fiat Ducato profile.
Step 5
Shop practice Read the transmission codes and photograph them before you clear anything.
Step 6
Check on the van Open the module’s procedures or active-tests list and find all four routines. AlfaOBD may word them differently. On related Fiat and Alfa boxes, owners report names like “Accumulator depressurization”, “clutch bleed” and “End of line / service self-calibration”. Nobody has published AlfaOBD’s name for Reset of Data Group on this van. Photograph the list. Don’t run anything yet.
If AlfaOBD doesn’t show all four, stop and use another scanner. Snap-on’s coverage guide lists Quick Learn, New Actuators, Hydraulic Circuit Depressurization, Learn Clutches Contact Point and Reset of Data Group for the 2014-and-newer ProMaster, word for word the factory names. That line doesn’t name Bleed Hydraulic Circuit and doesn’t say diesel, so check for the bleed on the van too. A Ram dealer’s wiTECH does everything. No public source shows Autel, Launch, TOPDON or Foxwell running these routines on the 2014 M40. Don’t assume they can.
Using your own scanner? Fill in the box below, and the site will match these factory steps to your scanner’s menus.
3. Release the pressure
Step 7
Factory Van stopped, engine off, ignition on, maintainer connected. Run Hydraulic Circuit Depressurization. Do every step the scanner asks, and wait until it reports the routine is complete.
Step 8
Factory Turn the ignition OFF.
Step 9
Factory Unplug the pump’s harness connector (Ram calls it the “Selespeed Pump”). It’s on the hydraulic power unit, which has the pump motor, the accumulator and the pressure sensor.
Owner-reported Do this right away. Owners report the pump wakes up and recharges the system when a door opens or the key turns. Unplugged, it can’t.
Factory wording: “The hydraulic circuit must be depressurized and the hydraulic pump must be disabled before servicing the hydraulic components.” If the scanner’s depressurization fails or isn’t available, don’t go on. Pulling a fuse and waiting is only forum practice, not a factory method, and leaves you no way to prove the pressure is gone.
4. Get to the accumulator
Where this section comes from. Ram’s service text has no accumulator-only removal page. The best first-hand account is a Ducato Comfort-Matic owner, same van body and same transmission, who changed the pump and accumulator with the gearbox in place, battery box out, working from underneath. Another Ducato owner gives the same route: cab battery and box out, then work from underneath through the battery-box hole. Bill heard the same thing. It fits the ProMaster, whose battery sits under the driver’s floor, but nobody has published it for the ProMaster itself.
Step 10
Shop practice Leave the ignition off. Disconnect the battery, negative cable first. The maintainer comes off now and goes back on in step 22.
Step 11
Owner-reported Remove the battery and the battery box from the floor at the driver’s feet. A Ducato owner put it at about 20 minutes. Take photos of the cable routing and every connector before you unplug it.
Step 12
Shop practice Raise the van and put it on jack stands. Never work under it on a jack alone.
Step 13
Owner-reported From underneath on the driver’s side, find the hydraulic power unit on the transmission: the pump motor, the accumulator (a round canister with a hex on it), the pressure sensor and the lines. Use the battery-box hole above you to reach in or see. Match it to the Mopar diagram, where the accumulator is item 5.
If you can’t get a socket on it this way, stop. Don’t start pulling other parts on a guess. A Ducato owner says the whole power unit comes off with three Torx screws once the lines are off, but that is more work than this job needs. One ProMaster dealer pulled the transmission to change the pump assembly, but that was the pump, not the accumulator. Send Bill a photo of what you see first.
•
Fiat Forum: Comfort-Matic lack of hydraulic pressure, first-hand: battery box removed, worked from underneath, accumulator off with a 22 mm socket and breaker bar.
•
Fiat Forum: Ducato 2017 Comfort-Matic problem: remove the cab battery and box, then work from underneath through the hole.
•
Pössl Forum (German), Ducato 3.0: access to the power unit is “only from below.”
•
Mopar diagram, 2014 ProMaster control module serviceable parts: accumulator item 5, next to the pump, motor, pressure sensor and valve body.
•
ProMaster Forum P0944 thread: the dealer pulled the transmission to replace the pump assembly.
• Still worth reading in a normal web browser, for ProMaster owners’ first-hand notes:
M40MTA fluid bleeding procedure ·
2015 diesel transmission woes ·
AlfaOBD on the ProMaster
5. Swap the accumulator
Step 14
Shop practice Clean all around the accumulator before you loosen it. Put the catch pan underneath. Check that the pump connector is still unplugged.
Step 15
Owner-reported Unscrew the accumulator with the socket that fits its hex and a breaker bar. Owners say it can be very tight. Hold the power unit so you don’t strain the lines. Expect some fluid to run out even with the pressure released.
Step 16
Check on the van Put the old and new side by side: same thread, same seal face, same O-ring size. Fit the new O-ring (from call 1). Wipe it with a little clean 75W hydraulic fluid, never DOT 4 or grease. This is normal shop practice; Ram text doesn’t cover it.
Step 17
Check on the van Start the new accumulator by hand so it can’t cross-thread. Tighten it to the torque from call 2. Don’t guess the torque. This guide doesn’t print a number because no trustworthy source publishes one.
The old accumulator is still charged with nitrogen. Don’t drill it, heat it or throw it in the scrap bin whole. Recycle it like any other gas-charged part.
6. Fill the fluid, with the pump still unplugged
Step 18
Factory Find cap 2, the hydraulic reservoir. Not cap 1, the clutch (DOT 4) reservoir.
Step 19
Factory With the pressure still released, add Mopar C Series DDCT 75W Hydraulic Fluid (68092638AC) until it reaches the middle of the sight window. Use a clean funnel or syringe that has never held anything else.
Step 20
Factory Don’t fill to the lowest mark on the window. Ram says that mark shows the running level at 45 bar (about 650 psi), with the system pressurized, and “should NOT be used” for fluid level checks.
7. Put it back and bring the pressure up
Step 21
Factory Plug the pump connector back in, with the ignition off.
Step 22
Shop practice Put the battery box and battery back. Connect the positive first, negative last. Put the maintainer back on.
Step 23
Factory Ignition ON, engine not running. Reconnect the scanner. Run Bleed Hydraulic Circuit. Ram says to bleed any time the circuit has been opened, and swapping the accumulator opens it.
Step 24
Factory Have the scanner command the pump on (“Selespeed Pump On”) and let the accumulator fill up to pressure.
Step 25
Check on the van Look over the new accumulator and the lines for leaks. If live data shows pressure, it should hold steady, not keep dropping. GEARS Magazine (a trade magazine, not Ram) gives the normal range as about 522–667 psi (36–46 bar).
Step 26
Factory Recheck the level in cap 2. Pressurized, it sits lower in the window, and that’s normal. If it needs topping up, release the pressure with the scanner first, then fill to the middle again.
•
Ram service text: Control Unit Bleeding: “bleed the control unit any time a hydraulic circuit is opened. Use the scan tool…”
• P1CCB-00 test, linked in section 3: reconnect pump, ignition on engine off, Bleed Hydraulic Circuit, command the pump on “and allow the accumulator to pressurize.”
8. Relearn
Step 27
Factory Run Reset of Data Group. In Ram’s relearn table, this is the routine listed for an accumulator replacement.
Step 28
Factory Then run Quick Learn. Ram: “The QUICK LEARN routine must always be performed after the RESET OF DATA GROUP routine is performed.” Follow the scanner’s prompts exactly.
If the scanner asks for the steps in a different order, follow the scanner. Ram’s notes say to bleed whenever the circuit was opened, and that Quick Learn always follows Reset of Data Group. For the parts next to the accumulator, though, Ram’s table runs Reset of Data Group before the bleed. Some tools ask for that order, and the tool’s prompts win.
Step 29
Factory Don’t run New Actuators or Learn Clutches Contact Point. Ram lists them for other parts, not the accumulator.
9. Prove the repair
Step 30
Shop practice Lower the van off the jack stands first.
Factory Start the engine. Watch Transmission Temperature on the scanner and let it run until it reads HOT.
Step 31
Factory Read the transmission codes. Clear only the ones from the repair, then read again.
Step 32
Factory Foot on the brake, van stopped: select reverse, neutral and drive. Each should engage cleanly.
Step 33
Factory Road test: smooth take-offs, every gear up and down, no transmission warning on the dash.
Step 34
Factory Back at the shop: recheck the cap 2 level the same way as step 26, rescan for codes and look under for leaks again.
Owner-reported Check that the pump isn’t running over and over with the van parked. Frequent pump runs are the classic sign of a failing accumulator.
• Ram service text, Transmission Verification Test: run until Transmission Temperature is HOT, check fluid level, relearns, road test, check codes.
George’s GO / NO-GO checklist
- Dealer confirmed 68133085AA fits the VIN, and you have the O-ring.
- You have the accumulator torque from the dealer, ALLDATA/Mitchell or the part’s instructions.
- 2 quarts of Mopar 68092638AC on the bench, plus a clean funnel or syringe.
- The scanner connects to the transmission module on this van.
- You’ve seen all four routines on screen: Depressurization, Bleed, Reset of Data Group, Quick Learn.
- Battery maintainer on whenever the scanner is running.
- You can see how to reach the accumulator once the battery box is out. If not, stop and send Bill a photo.
Sources